Tools

Binocular Magnifier Back in Stock
Wear this handy magnifier with its Velcro clasp. One size fits all so it is always comfortable. Magnifier assembly tilts up out of the way when not needed. Fixed lens gives 1.8X magnification for most close-up activities. For a closer look, a second binocular lens tilts down inside the visor. For turbo peep mode, swivel the loupe in front of the right eye. Combinations are 1.8X, 2.3X, 3.7X, and 4.8X.
MP242 $14.95

Qty:

 

AUTHENTIC DENTAL EQUIPMENT CONTROLLER
"Moto-Tool" and container set includes controller cabinet for two tools with high/low speed and forward/reverse switch LED indicators. Beeps when in reverse. Single footswitch controls motor on/off. Stainless steel tray sits atop cabinet. AC power cord. One motor assembly with long autoclavable coiled cord.
92Z031 $79.95

Qty:
 

Baby Bench Vise
It's been said there's a little vise in all of us, and now it's been personified. This is so cute (and small) you'll want to mount it on your bench so you can admire it. The 1"-wide smooth jaw opens to about 1" . Sold as a jeweler's vise, it has most of the features usually found in bigger bench vises, such as dual guide pin, lead screw, sliding handle, anvil.
845MV $8.85

Qty:

 

6-Position Crimp Tool
6 Position (6P6C,6P4C, 6P2C) Modular Telephone Plug Crimping tool. It cuts, crimps and strips the wire. PN HT-2096

97Z022 $9.95

Qty:


POINTED DIAGONAL CUTTERS
These small (4.75") cutters are made of carbon steel and have sharp, pointed jaws, spring joints and rubber coated handles.
ZF06 $5.49 each
Qty:



WIRE FORMING PLIERS
These tricky little devils have one round, smooth jaw and its mate is concave. Just the thing for forming ringlets in wire or modifying springs. The box hinge is spring loaded for easy action. This stainless steel gem is a handy addition to any tool box.
725CR $9.95 each

Qty:


TRIMMING SCISSORS
Short, pointed, sharp shears leveraged by longish handles. Designed for precision trimming. Keep these four-inchers in your toolbox and you won't have to risk mama's ire by getting caught with her "good" ones.
SC2044 $3.49 each

Qty:


VELOCIRAPTOR PLIERS
Short serrated jaws get a grip on anything from UHF through microwave. Long handles give good leverage. If you've ever been frustrated when trying to keep pulling force on a component while unsoldering it, these probably would have helped. Stainless steel, box joint, spring-loaded, etc.
665VF $9.95 each

Qty:

 



DIGITAL POCKET MULTIMETER
Measures: Volts AC to 450 Volts, Volts DC in four ranges from 2 to 450 Volts. Measures: Amps DC
to 200 mA. Measures: Ohms in four ranges from 0 to 20000K Ohms. Comes with test probes attached
and full set of instruments.

96Z004 $14.95 each

Qty:


Fisher Safety Shades
These are impact resistant polycarbonate safety glasses to ANSI specs, Sunlight UV coated, Mfd. by Fisher Scientific.
25Z049 Unit Price : $6.95

Qty:


Jackson Protective IR/UV Glasses
These are force 5 (strongest IR/UV) polycarbonate safety glasses made. They are as dark as Stevie Wonder's glasses and have side windows too.
25Z050 Unit Price : $12.95

Qty:

 


Watch Back Removal Tool
This is a handy tool to remove the back of a watch for servicing. Three adjustable jaws move to fit all sizes of cases and sets of interchangeable bits (five different sets of three) are included to get a grip on any case back. This can pay for itself the first time you use it instead of taking your heirloom to a jeweler to get the battery replaced.
25Z034 Unit Price : 9.95 Temporarily Sold Out



Watch Battery Replacement Kit
Kit of eight tools which may prove handy when servicing the family and the neighbor's watches. Included are a small phillips screwdriver, flat blade jewelers screwdriver, a back removing tool, a coin sized screwdriver, metal tweezers, plastic tweezers, soft brush and a knife to slash your wrists if the watch doesn't work when you're finished.
25Z035 Unit Price : $12.95

Qty:

 


Akro-Mills Parts Bin
Akro-Mills made these nice stackable parts bins.
They can be stacked and pinned together or screwed to a wall fastened back to back etc. The bins (six per unit) are big enough to get your hand into (how nice) and large enough to hold a generous quantity of the typical component or hardware.
These sturdy blue units measure about 20 x 7 x 4", each half is lockable and tilts out to expose the contents of three bins. The row of notches across the middle top are calibrated from 1/16" to 1/2"; a clever way of having a handy measure for screw diameter. These would be great for kit assembly; have a different set for each kit.

25Z033 Unit Price : $7.95

Qty:


Nylon Lacing Tape Black
Black Nylon lacing tape, 250 yards long 0.121" wide microcrystalline wax impregnated. conforms to mil-spec MIL-T-43435A http://www.icorally.com/products/harnessing/pg30-31.htm
LTN-1 Black Unit Price : $21.80

Qty:



Nylon Lacing Tape White
White (Natural) Nylon Lacing Tape, 250 yards long x 0.121" wide, wax impregnated, mil spec.
http://www.icorally.com/products/harnessing/pg30-31.htm
LTN-1 White Unit Price : $19.50

Qty:


White Nylon Lacing Tape 500 yd
Nylon lacing cord, waxed, 500 yard spool 0.090" wide.
Mil Spec MIL-T-43435A. 50 lb breaking strength
http://www.icorally.com/products/harnessing/pg30-31.htm

LTN-2 White Unit Price : $21.80

Qty:


Black Nylon Lacing Tape 500 yd
Black Nylon lacing cord, 500 yard spool 0.090" wide, waxed mil spec
http://www.icorally.com/products/harnessing/pg30-31.htm

LTN-2 Black Unit Price : $23.80

Qty:



Waxed Nylon Lacing Cord 750 ft
Black braided Nylon wax impregnated lacing tape 250 yards long and 0.200 inches wide, tensile strength 135 lbs.Mil spec http://www.icorally.com/products/harnessing/pg30-31.htm
LTN-0 Black Unit Price : $31.20

Qty:



White Nylon Waxed Lacing Cord
Waxed Natural (White) 135 lb lacing cord 250 yds (9000 inches) of .2" wide crystalline wax impregnated tape for lacing cables or making rabbit snares. This material conforms to MIL-T_43435B and other unspecified specifications. made in USA http://www.icorally.com/products/harnessing/pg30-31.htm
LTN-0 White Unit Price : $27.75

Qty:


Monster Shrink Tubing
Three inch diameter (shrinks to approx 1/2 size) heatshrink tubing in four foot hunks. We think the mfr is 3M but the only id on the product is 113-006-009 and "tubin, (sp) heat shrink, 3"
It is black. A trick for shrinking this big stuff and having it come out looking professional is to wait till the missus is out and then coil your project up on a cookie sheet in her oven; slowly crank up the heat in about five minute intervals until it starts to shrink; then be patient. Allow plenty of time so you can let it cool off and get clear before she comes home.

113-006-009 Unit Price : $15.75

Qty:

 


IC Clips Test
Leadset two 2.25” IC clips on 3 foot wires 1 red, 1 black  wt. 0.08
23Z070 $3.49

Qty:


Test Clips to Test Probes
2 wires: 1 red, 1 black 36” long, 2.25” hook clips on one end test probes on the other
wt. 0.1

23Z071 $2.49

Qty:


Meter Probe Set
1 red, 1 black 40” long meter ends have small diameter 1/16” diameter probes
popular with the old Triplett VOM’s and inexpensive imports
 wt. .1
23Z072 $2.49

Qty:

 

Round Mirror

Telescopic Round Mirror on card. Flexible handle extends to 24 inches

801TMC $2.95

Qty:

 


Velleman AS4 Anti-Static Mat with Ground Cord
Features: dual purpose PVC-latex material can be used either as dissipative or conductive matting easy to clean and maintain.
Specifications:
material: PVC
dimensions: 11.8" x 22"
thickness: 0.08"
with grounding cord
surface resistivity: 10e7 ~ 10e10 ohm/m
charge decay: < 0.03sec

AS4 $11.49

Qty:



Velleman AS5 Anti-Static Mat with Ground Cord
Features dual purpose PVC-latex material can be used either as dissipative or conductive matting easy to clean and maintain.
Specifications
material: PVC
dimensions: 19.7" x 23.6"
thickness: 0.08"
with grounding cord
surface resistivity: 10e7 ~ 10e10 ohm/m
charge decay: < 0.03sec

AS5 $12.95

Qty:



DIGITAL LIGHT METER
Features

* light level measurements: from 0.01lux to 50000lux
* easy to use with single function switch, light pocket-sized device
* 3 1/2 digit LCD display with low-battery & overrange indication


Specifications

* light:
* measuring range: 200, 2000, 20000lux (20000lux range reading x10) and 50000lux (50000lux range reading x100)
* accuracy:
* < 10000lux: 5% of rdg + 10 digits
* > 10000lux: 10% of rdg + 10 digits
* repeatability: 2%
* temperature characteristics: 0.1%/C
* photo detector: one silicon photo diode with filter
* power supply: 1 12V A23 battery (included)
* measurement rate: 1.5 times per second, nominal
* storage temperature: 14F to 140F
* photo detector dimensions: 4.5" x 2.4" x 1.1"
* dimensions: 7.4" x 2.5" x 1.0"
* weight: 5.6 oz.

 SPEC SHEET 
DVM1300 $57.95

Qty:

 

Small Aluminum Bench Vise
Lightweight cast aluminum bench vise for assembly or hobby work. Smooth jaws reduce marring of fine furniture measure 2.25" wide and open to 2 inches. The handy clamp will fasten this little marvel to a workbench one inch thick. This would be great for tying flies or moths but is not recommended for blacksmithing.
04T013 $11.95

Qty:



Set of Five Pliers
This is a nice inexpensive set of tools for hobby or light industrial use. All of these tools have rubber covered handles guaranteed to at least 20 volts insulation resistance, all have spring loaded action. The 4.5" diagonal cutters are typical and will probably work well on wire 20ga and larger. The 5" needle nose feature serrated jaws and a wire cutter. The duckbills have heavy serrated jaws that should be good for gripping pulling and twisting. The miniature (4.5") electricians pliers are sure to delight miniature electricians with their cutter, pipe grip and serrated jaws. Last but not least are the nippers, these are handy for trimming wire, sniping off brads and as pullers for small nails and large staples, they do well as emergency fingernail trimmers.
04T014 $9.95

Qty:

 

WIPING/SPREADING TOOL SET Back in Stock
Four tools with six business ends designed for small work in spreading, trowling, grooving and poking. These are handy for PC board repair (epoxy the cracks and draw new traces with our Conductive Pen, 93Z002, or digging into places where the wiring is so thick it looks like a storks nest.
DD301 $6.60

Qty:

CARVING, SCRAPING & SCRATCHING TOOLS
Back in Stock

Four semi-sharp tools, each with both ends designed for getting into smallish places to whittle, chisel, scrape or just plain prod. These were designed for carving wax but are handy for electronics work. Stainless steel.
DD302 $6.95 each

Qty:

STRAIGHT CROSSLOCK TWEEZERS Back in Stock
Serrated jaw, spring loaded, Stainless steel tweezers 4" long. Quick release. Use as heat sink or grip and pull. Very handy.
508TW $2.30 each

Qty:

 
Daedal X-Y Micropositioner

Daedal Inc X-Y tables with micrometer type threaded drive screws for precise manual positioning. The travel is approximately 0.75" in each direction. Each table is about 2.6" square. No part number is visible on these stages but they are probably on their website somewhere.
04Z013 $169.00

Qty:

 

Metric Micrometer Driven Slide
A nice pair of metric micropositioners each measuring 50 x 60mm, the travel of the slide is 20mm. These can be mounted at right angles to make a X-Y table or at 90 degrees to create an X-Z configuration with the included bracket and hardware.
The micrometers are calibrated in mm. Similar products are offered by Daedal, Starret, Newport, Del-Tron and others.
These are also called translation stages and linear micrometers. These are in excellent used condition and are offered at a fraction of their original price.

04Z005 $189.00

Qty:

 

Pocket Sized Analog Multimeter
This little gem is hardly bigger than a pack of (cough) smokes.
It comes with probes and is ready to use. At this price keep one in the car and the boat, another in the RV, give one to the missus too. Features include: seven DC ranges, four AC ranges, two Ohms ranges, mirrored meter, current and dB measurements too. Handy dandy analog meter helps reduce possibility of false readings we often get with DMM's.

04Z004 $9.95

Qty:

T0801.gif (15953 bytes)MINI TEST LEADS

Jumper kits can be used for wiring of prototype circuits, test circuits or temporary re-routing of faulty or re-worked boards.

•Insulation Resistance: 500VDC, 100 MW

• BK=Black, Y=Yellow, G=Green, R=Red, W=White.

Order #

Price

Description

# Leads

Clip

Length

Weight

T0802

$5.95

2 ea: R, BK, G, Y, W

10

Alligator

22"

0.5

T0803

$4.95

Large 1 ea: R, BK, G, Y

4

Alligator

39"

2.65 oz.

T0824

$2.95

2 each red and black

4

Alligator

39"

0.5

T0834

$4.25

Medium 1 ea: R, BK

2

Grabber

39"

0.71 oz.

 


Ersin Multicore Solder and Flux Combo
Ersin p/n QQ-S-571d solder and flux package. The box contains one pound of Ersin Multicore solder 60/40 alloy diameter .080" (14AWG, 2mm). The other component is Ersin Flux, this is high quality homogenized non corrosive rosin flux with properties that will lower the surface tension of the molten solder and provide a rapidly whetting joint that will remain free of corrosion even after prolonged exposure to moisture.....good stuff!
04Z041 Unit Price : $14.95

Qty:

 

Soldering Iron Tip cleaner

3.54"

VTSTC 8.98

Qty:



Digital LCD Panel Meter 3-1/2 Digit
Features:
3 1/2 LCD panel meter
single 9V DC operation
power consumption: 1mA DC
high input impedance: > 100Mohm

Specifications:
display: 3 1/2-digit LCD
input sensitivity: 200mV FS
power supply: 9V DC (7 - 12V DC)
decimal point selection: with wire jumper
automatic polarity indication
figure height: 0.52"
sampling rate: 2 - 3 readings / sec.
guaranteed zero reading for 0V input
high input impedance: > 100Mohm
accuracy: 0.5%
power consumption: 1mA DC
size: 2.7" x 1.7"


PMLCD 11.95

Qty:



Analog Panel Meter 0-15VDC,

Small Moving coil panel meters for use in electronic instruments, switchboards, vehicles,... With zero adjusting screw. Class 2.5. 2.4" x 1.9"

AVM6015 8.95

Qty:



Analog Panel Meter 0-30VDC

Small Moving coil panel meters for use in electronic instruments, switchboards, vehicles,... With zero adjusting screw. Class 2.5. 2.4" x 1.9"

AVM6030 8.95

Qty:



Analog Panel Meter 0-150VAC

Small Moving coil panel meters for use in electronic instruments, switchboards, vehicles,... With zero adjusting screw. Class 2.5. 2.4" x 1.9"

AVM60150 8.95

Qty:



Analog Panel Meter 0-300VAC

Small Moving coil panel meters for use in electronic instruments, switchboards, vehicles,... With zero adjusting screw. Class 2.5. 2.4" x 1.9"

AVM60300 8.95

Qty:



Analog Panel Meter 0-15VDC

Large Moving coil panel meters for use in electronic instruments, switchboards, vehicles,... With zero adjusting screw. Class 2.5. 2.8" x 2.4"

AVM7015 8.95

Qty:



Analog Panel Meter 0-30VDC

Large Moving coil panel meters for use in electronic instruments, switchboards, vehicles,... With zero adjusting screw. Class 2.5. 2.8" x 2.4"

AVM7030 8.95

Qty:


Power Outlet Strip
These are basic six outlet power strips with illuminated rocker switches. The specifications are typical; 115VAC,15 Amps, 1875 Watts. The housing is made of molded sealed plastic but you still cant take it in the pool with you. In fact it is recommended for indoor use only. It has a couple of handy screw slots on the backside so you can attach it to the wall, floor, ceiling...We bought too many of these so for a limited time (when the time is up you won't be able to read this) We'll sell you five of these for ten dollars; refer to part number 00401S. Not exactly 'free to a good home' but a heckuva deal!
04Z001 $2.95

Qty:

Power Outlet Strip Package of 5 above

04Z002 $10.00

Qty:

 


Starrett Depth Micrometer
Starrett # 263 Depth Micrometer measures in .001” increments to one inch. These have been used in a robotics application for precision changes in adjustment 5" x .75” wt 0.5
23Z074 $19.95

Qty:



Weller WHA300 Hot Air Soldering Iron used to cure epoxy.
Manufacturers description: Weller Hot-Air SMT Rework Station
Features a powerful 700W handpiece with a temperature range of 122F to 1022F 86F to handle most benchtop rework jobs. Temperature and air flow are controlled on a highly visible front panel with dial-adjustable controls. Extremely compact size uses less space on the bench. Operates on 120VAC and comes with hot air handpiece and power base with built-in handpiece holder. Interchangeable hot air nozzles must be purchased separately. Uses house air 10-50 liters/min.


Good used condition, sold less vacuum pump, regulator and airswitch.
WHA300 Our price $99.00

Qty:

 

Tuning Wand Tool, aka Diddlestick
Used to adjust analog circuits. Tool adjusts trimmer caps, pots, coils and the like. This 7" long tool has a screwdriver tip on each end. A little filing and the end can be reworked into a hex, square, or whatever your need is, that's why we sell them in pairs.
23Z041 2 for $0.99

Qty:


9-PIECE METRIC BALL DRIVER SET
1.5 - 10mm. Bondhus #10999.
22T003  $12.94 each

Qty:



13-PIECE SAE BALL DRIVER SET
0.05" to 0.375". Bondhus #10937.
22T002  $15.94 each

Qty:



7-PIECE HEX FOLDUP
2mm - 8mm, Bondhus #12587.
22T004  $6.00 each

Qty:


9-PIECE SAE HEX FOLDUP
0.5" - 0.1875". Bondhus #12591.
22T005  $4.79 each

Qty:


8-PIECE TORX FOLDUP
T6 to T25. Bondhus 12632
22T006  $11.88 each

Qty:

 

AC Voltage Tester
Non-contact Test, Voltage Sensitivity: 100 ~ 240VAC, Frequency: 50/60Hz, Detection distance: <5mm, Over Voltage: 600V, Operating Temperature: 0 ~ 50C, Storage Temperature: -20 ~ 60C, Humidity: <85%HR, Battery: 2AAA, Dimension: 148 X 20 X 25mm, Weight: 40g, Safety: For indoor use only and in accordance with over voltage.
AC110VD $6.99

Qty:

 


Advanced Digital Multimeter
3 1/2 Advanced Digital Multimeter with Temperature and Frequency measurement
3 1/2 digit LCD (1.0" digit height),
AC Voltage: 200mV ~ 700V, DC Voltage: 200mV ~ 1000V, Resistance: 200 ~ 200MOhms, Capacitance: 2nF ~ 200uF, Frequency: Up to 20KHz, Temperature: -20C ~ 1000C, Diode, transistor, and continuity testing, Includes manual, testing probe, temperature probe, yellow rubber base, Two 9Volt batteries included: one battery is installed and one spare. Maximum display: 1999. LCD display size: 43mm x 68mm. Size: 4.0"W X 2.0"D X 8.0"H, Weight: 1.6lbs
20Z002 $49.95 each

Qty:


Clamp Meter 
LCD size: 1547mm
AC Voltage: 200/600V, DC Voltage: 2/20/200/1000V, Resistance: 200 ~ 2MOhms, AC Current: 200/600/1000Amp
Frequency: 2KHz, Diode, continuity testing, Data Hold, manual, test lead, and 9Volt battery included
Size: 70X230X37mm, Weight: 310g 11ozs
AC2891 $69.95

Qty:

Advanced Clamp Meter
Display: Digital and Analog display, 3200 counts and 33 segments bar graph. Digits are 15mm high
AC Voltage: 750V, DC Voltage: 1000V, Resistance: 30MOhms, AC Current: 1000Amp, DC current: 600Amp, Max. Diameter for Conductor: 50mm
Frequency: 30KHz, Diode, continuity testing, Data Hold, Auto Range, Back Light, manual, test lead, and 9Volt battery included
Size: 282X2104X47mm, Weight: 500g 1.2lbs

AC2892 $109.00

Qty:

Solder Pot
Pot Capacity: 1.8Kg, Pot Construction: Stainless steel, Rocker On/Off switch, Wide Temperature control, Power 600 Watt, Pot Temperature: 300~500C, Pot Diameter 100mm, Pot depth: 45mm, 
Size: 140 X 1454mm, Weight: 1.8Kg 4lbs

AC60P $89.00

Qty:

AC25S Soldering Iron
Features: Easy to handle with rubber grip, Bakelite strong handle, Voltage: 110VAC, 60Hz, Power consumption:25W, 

AC25S $5.99

Qty:

 

94Z002.gif (19806 bytes)100 MHz SCOPE PROBE
Attenuation: X1 @ 10 MHz, 75pF, X10 @ 100 MHz, 11pF. Working voltage: 600VDC (including AC peak). Compensation range: 15-50 pF. Include 6" ground lead, spring hook, BNC adapter, I.C. tip, insulating tip, and trimmer tool. American-made.
94Z002 $24.50 each

Qty:

 

20Z007.jpg (5660 bytes)SOLDER SUCKER
Small size makes for easy one-handed operation. Aluminum barrel with Teflon tip.
20Z007 $4.99 each

Qty:

DESOLDERING PUMP Back in Stock
High suction power, ideal for PC board repairs. Light-weight, one-hand operation.
98Z013 $5.99 each

Qty:

Super Solder Sucker Pump Desoldering Tool

Supersoldersucker features include: superior quality, large capacity, powerful spring loaded piston, one handed operation.
One piece piston and plunger for easy cleaning. Protective hand guard makes operation safe. Good for sucking flies off your workbench during periods of boredom. Hint: lubricate it with Vaseline, keep it clean and it will last a long time.

04Z031 $7.95

Qty:

 

99z009.jpg (243764 bytes)LINERLESS RUBBER SPLICING TAPE
For low and high voltage (through 69KV). Based on Ethylene Propylene Polymers (EPR), this tape can be used on cables whose emergency overload temperature can reach 130C. Scotch 130C. 1 in x 30 ft (10 yds) x 0.03 in.
99Z009 $3.95/roll

Qty:

 

20Z012.jpg (8855 bytes)Basic Pocket Digital Multimeter 
3 1/2 digit LCD (0.5" digit height),
AC Voltage: 200V ~ 750V, DC Voltage: 200mV ~ 1000V, Resistance: 200 ~ 2MOhms, DC Current: 200uA/2mA/20mA/200mA/10A, Diode, transistor hfe testing, manual, test lead, and 9Volt battery included. Size: 2.6"W X 1.0"D X 4.8"H, Weight: 0.5lbs

20Z012 $9.95

Qty:


 
 889ws.gif (7081 bytes)5" ADJUSTABLE WIRE STRIPPER
Rubberized handles and grip.
889WS    $7.95
Qty:

 

843mv.gif (4728 bytes)MINI CLAMP-ON TABLE VISE
This handy little gem will clamp onto tables and benches up to 1" thick. Two screw holes are provided so it can be permanently attached. The jaws are 1.75" wide and will clamp work-pieces up to 1" thick.
96416CV $8.75 each

Qty:

 
 

95z025.jpg (7662 bytes)7-PIECE TORX WRENCH SET
Each wrench is made of high-alloy chrome-vanadium-molybdenum steel. Hardened and finished in black. Includes a plastic tool holder to keep them together as one unit. Each tool is double ended and resembles the better-known "Allen" wrench. Tool sizes are T6, T7, T8, T9, T10, T15 and T20.
95Z025    $12.95/Set

Qty:

   33-Piece Security Screwdriver Bit Set
"Wow! a person should be able to get into any small appliance with these. We don't even know the names of these tools but they appear to be; hollow torx, hollow 5 sided, three bladed, four bladed, and notched screwdriver bits and others. This is one of those tools a person won't often need but will pay for itself the first time it's used."
04Z003 $5.99
Qty:

750sd.jpg (10349 bytes)JEWELERS' SCREWDRIVERS
Six small screwdrivers (four straight blade and two Phillips) come in handy storage box.

750SD    $1.85/set

Qty:


 

93u002-a.jpg (10935 bytes)HELPING HANDS MAGNIFIER
Ball joints on all angles. Nickel-plated fittings. Heavy cast iron base. 2X 2.2" magnifying glass. Alligator spring clips. Locks at any angle.
93U002    $5.95 each

Qty:

 
 

Ec_100.jpg (4490 bytes)ECOHEAT™ HEAT GUN
An economical, lightweight, multi-use heat gun with two heat settings (500 and 1000F). Has 3-position slide switch, built-in hand guard, 3-wire grounded cord, thermoplastic case. UL listed, 120VAC.
EC-100    $32.95 each

Qty:

MINI HEAT GUN 11 and HEAT SHRINK TUBING
* Small, compact, lightweight heat gun with nozzle temperature to 1000F. Uses standard 1lOVAC outlet. 6-foot electrical cord with workbench storage loop. U/L recognized.
* 60 pieces of heat shrink tubing from' 1/8" to 1/2". Tubing shrinks to half original diameter.

20Z003 $39.95 each  

Qty:

 

 Assorted Heat Shrink Tubing
Sixty piece replacement for tubing in our 20Z003, including 1/8", 3/16", 1/4", 3/8" and 1/2" pieces 5" long

20Z006 $8.95 each 

Qty:


1/16" Heatshrink Tubing 100ft
Polyolefin 1/16" heatshrink tubing from 3M (p/n FP-301) or JT&T. brand. This material shrinks to half its size when threatened. 100 foot spool being offered here at a very low price.
25W019 Unit Price : $5.95

Qty:



3/32" Heatshrink Tubing 100ft
This is black 3/32" Polyolefin heat shrink tubing, it will shrink to half of its diameter with a suitable application of plasma. We have two brands: 3M p/n FP-301 and JT&T 4002S-0 on 100 foot spools. This is a popular size; stock up while it lasts.
25W018 Unit Price : $5.95

Qty:

Heat Shrinkable Tubing

Operating Temperature Range: - 55C to 135C
- 67F to 275F
Shrink Ratio: 2 to 1
Shrink Temperature: 121C/250F
Colors: Type 1, flame-retardant: Black,
White, Green, Red, Blue, Yellow
Type 2, not flame-retardant: Clear

 

Part Number Matrix HIX Price (4-Foot Lengths)

Size Black Clear Red Yellow Blue White Green (All Colors)
1/16" 8501 8511 8521 8531 8541 8551 8581 $1.50
3/32" 8502 8512 8522 8532 8542 8552 8582 $1.70
1/8" 8503 8513 8523 8533 8543 8553 8583 $1.80
3/16" 8504 8514 8524 8534 8544 8554 8584 $2.25
" 8505 8515 8525 8535 8545 8555 8585 $2.75
3/8" 8506 8516 8526 8536 8546 8556 8586 $3.10
" 8507 8517 8527 8537 8547 8557 8587 $3.45
" 8508 8518 8528 8538 8548 8558 8588 $4.75
1" 8509 8519 8529 8539 8549 8559 8589 $6.50
1" 8510 8520 8530 8540 8550 8560 8590 $11.50


Melcor Low Temp Bismuth Tin Wire Solder for TEC's etc.
Melcor part number 16-65-019-01 bismuth tin wire solder pack.
This kit includes 2 feet of Eutectic low (138 deg C) temp solder (Indalloy # 281) and the instruction sheets, spec sheet and warning sheet (don't eat it). 

04Z054  Unit Price : $2.95

Qty:


Miscellaneous IC Test Clips 

These are mostly AP products brand or similar, some are used but in serviceable condition. The range is for all standard dip packages up to 64 pins, leads are gold plated to improve signal transfer.

SKU              Description               Price
TC-14    Test Clip 8/14 pin

      $4.95

TC-16

    Test Clip 8/14/16 pin

      $4.95

TC-18

       Test Clip  16/18 pin

      $6.95

TC-20        Test Clip 18/20 pin

      $6.95

TC-24        Test Clip22/24 pin

      $7.95

TC-28        Test Clip 28 pin

      $8.95

TC-40       Test Clip 40 pin

     $11.95

TC-64      Test Clip 64 pin

      $19.95



 

 

MORE TOOLS