Hardware

Hardware

2" Stroke Gas Shock
Camloc varilift gas spring (aka Arvin Motion Control) p/n SVV6S060096S6D-400N-129747-28/00. end mounting hardware included as pictured. The stroke is approx 2" and the lift is approx 20 lbs. By inverting this product it may be used to lower a lid rather than raise it.
25Z102 Unit Price : $9.95

Panduit Tie Wrap Mount 1000 pcs.
Panduit p/n TM1S4-M natural tie mounts for use with #4 (M2.5) screw and miniature cable ties. SPEC SHEET
Compare our price with others at more than double our price. These are reputed to be the same type of mounts that the Lilliputians used to secure Gulliver.
25Z098 Unit Price : $89.95

Hayward 1/2" Needle Valve
Hayward NV10050T 1/2" PVC needle valve threaded.
25Z097 Unit Price : $29.95

Phoenix Contact DIN Terminal
Phoenix Contact din rail snap on barrier terminals p/n 03 04 38 8. Made in Germany, in the Black Forest, by elves.
25Z095 Unit Price : $0.49

George Fischer 1" ball valve
George Fischer 1" ball valve p/n161.346.314 PVS hi pressure/hi rel.
25Z093 Unit Price : $12.95

George Fischer 3/4" ball valve
George Fischer p/n 161.343.673 PVC hi pressure three way ball valve.
25Z094 Unit Price : $13.95

Siemens Rotary Door Mounted Operating Handle
Siemens p/n D11CFU2 rotary door handle for electrical equipment.
25Z084 Unit Price : $49.95

Steel Non-skid Stud Leveler
S&W Mfg p/n NSW-3A-SP-3. 6000 lb rated stud leveler (Jackscrew), made of steel, thread is 5/8-11,base has a rubber cleat and measures 2.5" dia, the shaft is 4" long, locknut included.
25Z085 Unit Price : $2.49

Asco Red Hat Valve 8210G88 120V AC
ASCO Red Hat general purpose 3/4" solenoid valve with 120V AC coil, 2 way pilot operated stainless steel. This valve is normally closed (energize to open).
25Z086 Unit Price : $249.00

Ryan Herco Horizontal Port Valve
RyanHerco p/n 5831.125 ACR RTMTR 180 SCFH 1/4" 50mm S
Acrylic Body with 1/4" fpt brass ports.
25Z087 Unit Price : $23.95

Gems Flow Switch 155485
Gems p/n 155485 Flow switch made in USA. 24V DC, 1/2 npt, visual flow feature, 4 to 20 gpm, polypro construction.
25Z082 Unit Price : $74.95

3-Way 3/4" Ball Valve
Ipex 3 way valve; this is a 3/4" plastic high pressure, high quality ball valve. Ipex calls it a 'T' port 3 way ball valve p/n VTBV104 it may also be marketed as a FIP co. p/n VT-ERGO
25Z083 Unit Price : $29.95

PVC Union 1/2"
Spears p/n EV1B13 grey PVC union for 1/2" fluid lines. These have threaded ends and an 'O' ring seal.
25Z077 Unit Price : $2.99

George Fischer Ball Valve
George Fischer p/n 161.346.313 Type 346 PVC Socket/Threaded 3/4" NPT True Union Ball Valve with FPM seals and Teflon seats.
25Z078 Unit Price : $11.95

Heavy Duty Tarp Clamp
To use this 3" clamp, slip a rope into the hole, slide bar forward, and the jaws will ratchet fast against tarp or awning. Many other possible uses.
99Z008 $1.99 each

3" Carabineer
Carabineer made of anodized aluminum with spring loaded stainless steel insert. This three inch wannabe mountain clasp features a built in compass (for no apparent reason) but it actually works! By using this item as a keychain you are virtually guaranteed not to get lost inside your car.
25Z073 Unit Price : $1.39

EMI Shielded Strip/ Finger Stock
EMI shielding commonly used around doors and between sections of a chassis. This one is approx 15 feet long and 3/8" wide. The finger stock has sticky tape on the backside and the fingers are 1/4" wide. It's been spooled onto surface mount component spools.
25Z063 Unit Price : $19.95

Ion Exchange Resin
Miyachi Exchange resin for ML-2xxx series welders. This product is their part number MLF-0021.
25Z061 Unit Price : 23.95

Hole Plug, metal 1/2"
Metal hole plug for 1/2 inch holes, nickel plated steel.
Cover up access holes or mistakes.
25Z054 Unit Price : $0.25

Sticky Holders for Zip Ties 20 pieces.
Sticky backed plastic holders for tie wraps. These handy little jewels have a peel off back, the sticky adheres well to most any surface, each piece is 3/4" square and can have a tie-wrap threaded thru it from the south or the east ( unless you're left handed...). remember you're getting 20 pieces for one price.
25Z045 Unit Price : $0.99

Adjustable Coupling
Metal adjustable 180 degrees mechanism could be used on a lamp or a microphone or magnifier. It has a lock to keep it in position. The 1/2" diameter threaded bushings can be turned into a tapped hole or nutted onto a panel. These have an ample passage thru the body to allow for wiring or cable. Approx size is 1 x 1 x 4".
25Z041 Unit Price : $0.99

Event Counter
ITT 24VDC (pulse) event counter part number CE40BN5016. General Controls division made this device, it's rated at seven Watts and features five odometer style digits about 1/4" high. Each device has a few counts showing on the dial and measures about 1.75" square and 2.5" deep. Mounting tab is on the front.
25Z006 Unit Price : $4.95

Shock Mount Vibration Damper Military Style
These appear to be military of the type used to mount electronic equipment, no manufacturer's name is on these but there is a part number; 47038410. They are quite stiff, probably used for heavy stuff, each measures 1.5" between the eyes, height is 1/2", width 1&1/8". A stainless steel #10 allen bolt has been generously supplied with each unit.
04Z047 Unit Price : $0.99

Hex Standoff
Hex standoff 1 inch long x 1/4" diameter with threaded 6-32 holes in each end. Bright metal finish.
04Z045 Unit Price : $0.39

Hex Standoff
Aluminum hex standoff 1/2 " long x 1/4" diameter. Each end has 6-32 threaded hole. Inquire about 100 lot discount.
25Z002 Unit Price : $0.39

Deluxe Knob
Heavy duty index knobs feature bright metal trim, white index mark, flat grey plastic finish and a metal insert that fits over the 1/4" shaft. these are designed to fix on a round shaft by means of two hex setscrews which are included. This is not cheap made in Antarctica by penguins stuff; it's really robust and will look good on your teleporter or HiFi or whatever. Measurements 1" dia. x 3/4" high.
25Z003 Unit Price : $0.95

Plastic Knob 1.5"
These plastic knobs are designed to press onto a 1/4" knurled shaft. The skirt is about 1&5/8" in diameter and it is about 5/8" deep, black.
04Z048 Unit Price : $0.49

Pointer Knob
Black pointer knob with white stripe on pointy part. These are about 1&1.2" long and 7/8" wide and 1" high. They need a setscrew to fasten them to a 1/4" shaft.
04Z049 Unit Price : $0.59

Nifty Knob
High quality knob, fluted for easy grasping and gentle tweaking. These have a nice feel to them and a rubber skirt attached to a hard plastic body which has a wrinkle finish on the front, they are made for a 1/4 inch shaft press-on type.They measure 1.5" dia. x .75" high.
04Z050 Unit Price : $0.89

Shiny Control Knob
Bright metal finish on plastic knob with geared skirt. It's kinda hi-tech looking, lightweight plastic insert in metal cap. These are made to push onto 1/4" serrated shafts and measure about 1" x .5".
04Z051 Unit Price : $0.49

Joystick Knob
Neat 3/4" raised knobs to crown your joysticks.
93V001 0.99

INDEX KNOB
Black plastic knurled knob, 0.625" dia, 0.75" high. Fits standard 0.25" half shaft.
92Z039 6 for $1.00

92Z049 100 for $10.00

White Control Knob
White knob with index stripe and serrated edge. These 1&1/4" diameter x 5/8" high plastic knobs have a metal insert made for a standard 1.4" dia. round shaft, they are tapped for a a setscrew. This is quality stuff ; not some cheap imported thingy.
25Z066 Unit Price : $0.89

Deep Reach Knob
Plastic knob with chrome metal finish and index stripe, black insert. These knobs fit a 1/4" serrated shaft and have a 3/4" sleeve to reach through the panel to grip the shaft. The knob diameter is about 7/8" and it is about a 1/4" thick.
25Z067 Unit Price : $0.69

Small Black Knob
Black plastic tweaker knob with silver accent ring measuring 7/16" diameter and 5/8" deep for 3/16" keyed shaft. Metal insert promises a firm grip and protects against splitting. Torque spec unknown but is probably less than 900 ft/lbs.
25Z068 Unit Price : $0.49

Tuner Knob with Gold Insert
Plastic knob similar to those used on the fine tuning shaft of analog TV tuners. The shaft gripping sleeve is designed for a 1/4" shaft with two flats as seen on TV tuners and dual pots like stereo faders and volume controls etc. these reach thru the panel 3/8" and are about 1.5" in diameter.
25Z069 Unit Price : $0.59

HANDLE
2 3/4x1x7/16 round aluminum Price per pair. 8-32 thread 1/2" deep.
22Z028 $2.45

Qty:

Equipment Handle 4" Metal
Winchester Electronics/USECO is the maker of these bright finish round handles. these are the style commonly found on test equipment. Their part number is LS 8386 4, the spacing between the mounting holes is 4.25". The depth of the handle is 1.5". Sold as a pair, individually bagged.
25Z001 Unit Price : $2.69/pair

Equipment Handle 3" pair
Brushed Aluminum handles for electronic equipment, 3" mounting hole pattern. Sold in pairs at this price, individually bagged, screws included.
25Z101 Unit Price : $2.69

Control Knob; Small Bakelite
H. H. Smith catalog number 2240 brown plastic knob. These pointer less knurled knob will fit on a full round 1/4" control shaft and have a setscrew. Each knob is 3/4" in diameter and 3/4" high. These attractive knobs harken back to the '40's and 50's in style. They glisten with pride of workmanship.
04Z037 Unit Price : $0.89

Control Knob
Skirted knob for 1/4" shaft with setscrew, black with brass insert, 1" dia. x 3/4" high.
04Z057 Unit Price : $0.59

Big Knob for Variacs and the like
These are index knobs emblazoned with the S/E logo (Superior Electric?) Each has a glossy black finish and measures 2.75" dia. They are designed to fasten to a 3/8" shaft with two setscrews.
04Z058 Unit Price : $2.89

Hex Standoff 3.5"
Plated brass hex standoff with 8-32 stud on one end and corresponding tapped hole on the other. These 1/4" dia. chrome standoffs measure 2&1/2" long.
04Z042 Unit Price :$0 .99

Brass Hex Standoff 5"
Chrome plated brass hex standoff with 6-32 stud and socket measuring 5" long x 1/4" diameter.
04Z043 Unit Price : $1.29

Southco Magnetic Door Latch Assembly
Southco made these magnetic catches which are commonly found on electronic enclosures. Each plastic encased magnet measures about 1&1/2 by 3/8 by 1" deep and would snap into a rectangular hole of that size. the striker is a metal plate with a single mounting hole measuring 1&1/4 by 3/4 inches.
04Z044 Unit Price : $1.99

H H Smith Ceramic Standoff
H H Smith number 2538 bushings. Threaded ceramic insulators 1/2" long and 3/8" in diameter with 6-32 threaded holes in each end.
04Z038 Unit Price : $0.65

Humongous Standoff 17" aluminum
The ends are threaded for 8-32 screws, these are 3/8" in diameter and 17" long. Stir your martini, use them as elements on a uhf Yagi, high tech chopsticks?
04Z039 Unit Price : $1.69

Hex Standoff 2.5" aluminum
J S Bennett company hex standoffs p/n 8237-B-0632.
These have 6-32 treaded holes in each end and are 2.5" long hexagonal aluminum 0.25" in diameter. buy some now.
04Z040 Unit Price :$0 .95

Humongous Hex Standoff
Aluminum hex standoff 4" long x 3/8" dia. These have threaded holes each end; 6-32. Keep several handy, be prepared to put a hex on anyone whom offends you.
04Z030 $0.99

Carry Handle
For test equipment or carrying case or tool boxes. Strap type handle lies flat against product, spring steel insert causes it to fall flat against case when released. Metal end caps secured by screw from inside product. Overall length 9" X 1" wide. This is the type of handle commonly found on the top of oscilloscopes.
99Z010 $1.89 each

Snap Button Hole Plug
We call them “goof Plugs” because often we use them to fill a hole we drilled in the wrong place. Nickel plated steel snaps into 1” hole in chassis or panel of .060 to .1” thickness. Some variation in panel thickness and hole size can be compensated for with additional determination, pliers application and RTV.
23Z059 6 for $1.00

Aluminum Pinion Rod
Each piece is 7-1/4" long and 2-3/4" diameter. Mfg is unknown is stamped Made in Germany and bears a logo of a "B" in a circle. The material is uncut and unused.
23Z024 $39.95

Caster with ball bearing swivel mount.
Wheel is 4 inches in diameter and 1 inch wide. 0.5 inch diameter stem is 1.375 inches long. Mfg: Triopines Dimensions: 7 x 4 inches Condition: New, no box. Weight: 1.30 lbs
23U612 $4.95 each

Caster with 'Vari-Flex Suspension'

Designed for shock absorption. Quiet, smooth operation minimizes damage to floors. Weight handling range 100-500 lbs. Wheel is 4 inches in diameter, 2 inches wide. Mfg: RT Laird Inc. C1081L Condition: Used Weight: 10.00 lbs
23U611 $34.95 each

Caster with 'Vari-Flex Suspension'
Designed for shock absorption. Quiet, smooth operation minimizes damage to floors. Weight handling range 100-380 lbs. Wheel is 3 inches in diameter, 1.5 inches wide.
Mfg: RT Laird Inc. R1163T Condition: Used
23U610 $24.95 each

Casters 5" Diameter
Single Wheel all metal with swivel mount.
23U005 $34.95 set of 4

Casters 6" Diameter
Single wheel ball bearing 2 with locks, 2 without non-swivel.
23U006 $38.95 set of 4

Casters 5" Diameter
Single wheel metal frame, plastic wheel with rubber tire. Non-swiveling.
23U007 $19.95 set of 4

Casters 5" Diameter
Single wheel metal frame. Plastic wheel non-swivel
23U009 $9.95 per pair

Casters 3" Diameter
Single wheel metal frame hard rubber tire. Used swivel mount.
23U010 $19.95 set of 4

RACK EQUIPMENT HANDLES
4-7/8" X 1-1/2" X 5/8" mounts with two 10-32 screws on 4-9/16" centers. Maximum depth in handle 3/4". Black anodized aluminum.
22Z013 $2.95 pair

22Z013S 10 for $12.00

Keystone Equipment Handle: pair
Keystone #7140 round instrumentation handle; these are ideal for 1U rack enclosures: They measure (A) 1.25" between the eyes and stand (B) 1" tall and are tapped for 4-40 threads. Our price is for one pair (two handles); inquire about reduced price when ordering 100 or more pair. Nickel plated brass.
25Z051 Unit Price : $2.49

EQUIPMENT RACK PANEL HANDLES
2-3/4"(70mm)W X 3/4"(20mm)H Tubular aluminum style. Tapped for screw mounting.
22Z012 $1.59 pair

22Z012S 10 for $5.95

RFI/EMI FINGER STOCK
Two-feet long by 0.5" "copper" color alloy with adhesive backing.
97Z006 $1.99 each

97z008.jpg (5545 bytes) SERIOUS FINGER STOCK
25' length by 1.5" wide alloy for RFI/EMI shielding applications.
97Z008 $19.95

Nylon Hex Tapped Spacer 100 pcs
Eagle Nylon Hex Tapped Spacer: These are tapped for 4-40 screws and are 0.875 inches long and 0.25 inches in diameter. These are hard to find now that Nylons have been placed on the endangered species list. We are selling these in bags of 100 pieces. Mouser offers these as their p/n 561-L4.875.
04Z015 $19.00

95z001.gif (24529 bytes) RUBBER FEET

Black, round, 7/16" dia. x 1/8" thick. 56 per sheet.

95Z001 $3.95 per sheet

RUBBER FOOT
3/4" diameter x 1/2" height. Mounts with 6- or 8-32 screw

20U003 16 for $2.00

SELF-ADHESIVE RUBBER FOOT
½" diameter x ½" height. Black

20U002 12 for $1.00

Rubber feet / Pipe End Caps
Rubber feet could also be used as a pipe plug or a cane tip.
These are designed to press into a 1/2" hole. The working part is 5/16" high and 3/4" in diameter. Large quantity available.
25Z039 Unit Price : $0.09

Qty:

98z012.gif (11668 bytes) GENUINE 14X JEWELER'S LOUPE
Brand new, first-quality glass Hastings Triplet flat field loupe made in the USA by Bausch & Lomb. If you're in the field searching part numbers on components or serial numbers on equipment, this little gem could pay for itself the first time you use it. Retails for $60!

99Z003 $29.95 each

SILICON VALLEY GOLD
Over fifty pounds of printed circuit boards from computers, monitors, modems, test, RF and microwave equipment, all stuffed with goodies such as toroids, ICs, switches, sockets, connectors, oscillators, crystals, transistors, diodes, varactors, etc. A gold mine of usable parts.
92Z037 50 Lbs. for $49.95

MORE HARDWARE ITEMS